2002 chevy cavalier starter replacement




Article Navigation:
  • Photo
  • Chevrolet Cavalier : starter removal and replacement | House of Woogeroo
  • Video
  • RELATED PAGES
  • A Chevrolet Cavalier Starter Replacement costs between $ and $ on average. Get a free detailed estimate for a repair in your area.

    Wrenching Chevrolet Cavalier: starter removal and replacement Details of the vehicle: Chevrolet Cavalier 4 door L ecotec engine 4 speed.

    Starter. GM Cavalier/Sunfire Repair Guide. TESTING 2: Remove the starter electrical connections from the back of the starter. Click image to see.

    Once the old starter is removed the process to insert the new one is done in reverse sequential order. Rest the starter at an angle, nose end down on the lower car frame below the radiator. Don't miss the small hose that goes under the air intake. Warnings When jacking the vehicle, be sure that you placed the jack in a proper location under the vehicle!

    Chevrolet Cavalier Starter Replacement Cost Estimate

    If your starter needs replacing and you don't have the immediate time and finances to send it to a shop, you may wish just go out on a limb and repair it on your own. This article will help you replace your starter on a Chevrolet Cavalier or a Pontiac Sunfire Automatic Transmission OHV 2.

    Car Batteries and Ignitions Chevrolet Vehicles. Edit Article How to Replace the Starter on a Chevy Cavalier If your starter needs replacing and you don't have the immediate time and finances to send it to a shop, you may wish just go out on a limb and repair it on your own. WD Lubricant Wood Blocks. Work Gloves and Goggles. Vehicles around this model year usually have a hood release lever under the steering column to initiate this step. Once done, lift the hood and insert the stick to hold the hood in place for operation.

    Disconnect the negative black cable from its battery post. Using an 8mm socket wrench or 8mm wrench remove the terminal nut from the negative cable and gently place it somewhere safe.

    Doing so will reduce the chances of sparking the battery and damaging any other electrical part in the vehicle. Simply press down on the brake as you press and the hold the button on the parking brake to pull up the lever until it locks the mechanism. Remember to block the rear wheels. Remove the terminal nuts and wires. Once the vehicle is properly raised, it's time to go under the vehicle. Place a carpet, mat, or cardboard box on the ground to lye on and remove the two terminal nuts with a 13mm wrench from around the electrical wires.

    Also, you can do this without going under the vehicle. Depending on your preference. Remove the bell-housing shield. This mechanical part is only on some OHV 2. If yours has it, there are 3 bolts that need to be removed from this plate. The first located face first by the starter and the second is below the starter. The other bolt is located on the other end of the plate between the oil and transaxle pan. Now that the plate is removed there are two 15mm bolts that are connected to the starter mount.

    Disconnect them with the socket and ratchet, and the starter will be removed. Once the old starter is removed the process to insert the new one is done in reverse sequential order. Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. Tips When jacking the vehicle the cross member or frame rails are excellent positions if you are not sure where to put it.

    You should shake the vehicle slightly to check if the jack stands are supporting the vehicle properly. Short and Long extensions would help for hard-to-reach places over and under the vehicle. Take your time this isn't a rush job. Use WD Lubricant to loosen up tight nuts and bolts.

    Having a Flashlight can help illuminate dark areas under the hood It's best to have a quality work space when working under certain conditions i. If you wear glasses place your googles over them for quality protection. Always keep your tools clean. Warnings When jacking the vehicle, be sure that you placed the jack in a proper location under the vehicle!

    Do not start working under the hood or the vehicle until you disconnect the battery cable s first! Be sure to wear Gloves to protect your hands and Goggles for your eyes while working under the vehicle! Avoid wearing long sleeve clothing. Do not have the car sitting on the floor jack for too long! Don't use any other tools other than the ones essentially assigned for this operation! When unscrewing nuts and bolts be careful not to strip them!

    Starter Replacement 04 Cavalier



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲